|
|
#1
05-02-2010, 09:27 PM
|
|||
|
|||
Project Calamity
Well its not quite as in depth as some on here but thought id do a little post,
After changing my clutch tone recomended to get me down pipe sorted as it started to blow,Obviously de-Cat was in order, For any1 thinking attempting this make sure you have ; 1, WD40 (by the Gallon) 2, Axle stands/Ramps 3, Loving wife that constantly brings you Teas and will take the occasional bit of abuse to relive the stress of that Bloody bolt not moving and finally a spare set of knuckles after you've removed yours on the poxy heatshield. Unlucky for me i had none of these until a mate popped round to lend a hand. Finally got the old pipe off just as it turned dark so will refit new de-Cat tomorow. Old nasty Pipe  New shiny one , well kinda , 2nd hand off fleebay  as i had to take off the intercooler to gain access to heatshield i thought id give it a good clean up n spray, Also gives me chance to look at the knock sensor   Also does anyone know if i have to put the turbo heatshield back on or can i leave it off? GTG now wifes due home and theres crap all over her dining table!!! 
|
|
#2
05-02-2010, 09:50 PM
|
||||
|
||||
|
Thats the hard bit done.
Putting the new one on is so much easier and lighter. Remember to trim the bottom off the top heatshield so it will sit back on top of the turbo/downpipe again and fix use the 2 rear bolts and the one on the side (at an angle) under the intercooler. Easier enough to do with a good hacksaw.
|
|
#3
05-02-2010, 10:01 PM
|
|||
|
|||
|
Quote:
Do a search on Sussex and Surrey for historic posts on this. Without one, the temp in the engine bay gets higher which can have a possible effect on the rubber hoses and also on the efficiency of some of the fluids.....
|
|
#4
05-02-2010, 10:45 PM
|
|||
|
|||
|
Quote:
Top part of Heatshield is already seperated as i undone everybolt i could see n it came apart when removing. Think i sheared 2 bolts off but none that were in any relevant places, Just trying to remove the sensor from exhaust at the mo but to no avail, What size is the spanner needed it mahooosive?
|
|
#5
05-02-2010, 10:55 PM
|
|||
|
|||
|
Good job matey.
|
|
#6
05-02-2010, 11:39 PM
|
|||
|
|||
|
Quote:
Will have a look in the morning, I have the special socket with the cutout for the wire in the shed. Was purchased when I did my Toyota. Most are 22mm, that is the size I have but you can also get 27mm ones as well.
__________________
2 Subaru's - 2007 R2 (660cc JDM kei Car) 1994 JDM Impreza WRX Last edited by Kei Man; 05-02-2010 at 11:47 PM. Reason: found it.
|
|
#7
05-02-2010, 11:55 PM
|
|||
|
|||
|
Quote:
Cheers for looking tho
|
|
#8
06-02-2010, 08:05 AM
|
||||
|
||||
|
You were braver than I was, I went to my mates to get his de-cat from his company and got him to fit it, meant a trek to sheffield but worth it as I got a free bacon buttie and coffee, good work Nick
__________________
Part of the team who created one of the largest subaru convoys to hit Brighton
|
|
#9
16-02-2010, 05:24 PM
|
|||
|
|||
|
Reading the posts about wrapping ppls downpipes, lookin to do mine now,
Titanium wrap looks the nuts,but how far down the pipe do i need to wrap? also was essin bout with paint today n its givin me a few future ideas on colours  I like the blue alloys, different
|
|
#10
16-02-2010, 05:42 PM
|
|||
|
|||
|
Quote:
The effect on the fluids will be minimal, likewise with the rubber hoses. Even less if you have samcos. Its mainly to do with heatsoak effecting the TMIC when there is no airflow to cool it, and some might say det on piston number 3 nearest the tubby. but i think this would be minimal still IMO. Quote:
Just wrap like this... maybe go another few inches further but it needs to go no further than that as the effect would be minimal. 
|
 |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
