South East Scoobies  

Go Back   South East Scoobies > The Garage > Engine Management

Engine Management For all your mapping,diagnostics and electronics

Reply
 
Thread Tools
  #1  
Old 20-04-2018, 10:25 AM
SpecB's Avatar
SpecB SpecB is offline
Moderator (formerly known as Bluebugeye!)
 
Join Date: Mar 2009
Location: Littlehampton
Posts: 4,345
Default Tactrix 2.0 and ECUFlash issues on 05 Legacy

Morning,

Do any or our resident experts have any idea why ECUFlash will not read the base map from my ECU - It will connect to the ECU but times out when reading. I have found out I need to connect the 'green connectors' however it appears my car has two sets, one in the passenger footwell and one behind the kick panel on the drivers side - the connectors on the passenger side do not appear to do anything no CEL or cycling of fans etc. when connected.
__________________
2005 Spec B 6MT - KiDO tuned (~270Bhp)
Custom exhaust - Cosworth filter - Samco Intake - Tints - Bilstein B8/B6 & STI springs - SuperPro ALK - Whiteline positive shift kit, rack mounts, rear adjustable camber bushes, front ARB mounts & strut brace, 20mm rear ARB with AVO mounts, - Hardrace Gearbox and pitch mounts - Prodrive PFF7's - Front Brembos - Kenwood CarPlay - 1/2 carbon grille - STI front splitter
Reply With Quote
  #2  
Old 20-04-2018, 11:25 AM
Scott.T's Avatar
Scott.T Scott.T is offline
Admin, Meets/Events Organiser.... formerly known as SilverSurfer
 
Join Date: Sep 2008
Location: Hastings, East Sussex
Posts: 9,485
Default

Should have some under steering column and sometimes the join in the passenger footwell behind the left kick plate trim are disconnected. So this needs reconnecting
Reply With Quote
  #3  
Old 20-04-2018, 12:26 PM
SpecB's Avatar
SpecB SpecB is offline
Moderator (formerly known as Bluebugeye!)
 
Join Date: Mar 2009
Location: Littlehampton
Posts: 4,345
Default

Cheers Scott

So if I'm right I need both connected to read/flash and if I disconnect either I have broken the circuit so only one needs to be disconnected to go back to normal mode?
__________________
2005 Spec B 6MT - KiDO tuned (~270Bhp)
Custom exhaust - Cosworth filter - Samco Intake - Tints - Bilstein B8/B6 & STI springs - SuperPro ALK - Whiteline positive shift kit, rack mounts, rear adjustable camber bushes, front ARB mounts & strut brace, 20mm rear ARB with AVO mounts, - Hardrace Gearbox and pitch mounts - Prodrive PFF7's - Front Brembos - Kenwood CarPlay - 1/2 carbon grille - STI front splitter
Reply With Quote
  #4  
Old 20-04-2018, 12:41 PM
Scott.T's Avatar
Scott.T Scott.T is offline
Admin, Meets/Events Organiser.... formerly known as SilverSurfer
 
Join Date: Sep 2008
Location: Hastings, East Sussex
Posts: 9,485
Default

Yes. Both connected to read.
Then just disconnect the one under the steering wheel when done.
I'm not sure if you also need the white jumper block to flash or the other blue spade block.
If your drive by wire you shouldn't need it much like a Hawkeye.
Reply With Quote
  #5  
Old 20-04-2018, 12:44 PM
Scott.T's Avatar
Scott.T Scott.T is offline
Admin, Meets/Events Organiser.... formerly known as SilverSurfer
 
Join Date: Sep 2008
Location: Hastings, East Sussex
Posts: 9,485
Default

Jumper blocks can be seen here https://rover.ebay.com/rover/0/0/0?m...2F202235664593
Reply With Quote
  #6  
Old 20-04-2018, 12:49 PM
SpecB's Avatar
SpecB SpecB is offline
Moderator (formerly known as Bluebugeye!)
 
Join Date: Mar 2009
Location: Littlehampton
Posts: 4,345
Default

Cheers,

Think I'm OK without the jumper as it's DBW and uses the same protocols as the Hawkeye to communicate with the ECU. I'll probably use the passenger footwell as the changeable connector as my drivers side blocks appear to be behind the kick panel so are a bit awkward to get to. I'll give it another go this afternoon then hopefully I can start getting the car mapped!
__________________
2005 Spec B 6MT - KiDO tuned (~270Bhp)
Custom exhaust - Cosworth filter - Samco Intake - Tints - Bilstein B8/B6 & STI springs - SuperPro ALK - Whiteline positive shift kit, rack mounts, rear adjustable camber bushes, front ARB mounts & strut brace, 20mm rear ARB with AVO mounts, - Hardrace Gearbox and pitch mounts - Prodrive PFF7's - Front Brembos - Kenwood CarPlay - 1/2 carbon grille - STI front splitter
Reply With Quote
  #7  
Old 20-04-2018, 01:15 PM
Scott.T's Avatar
Scott.T Scott.T is offline
Admin, Meets/Events Organiser.... formerly known as SilverSurfer
 
Join Date: Sep 2008
Location: Hastings, East Sussex
Posts: 9,485
Default

Drivers side should be up behind steering wheel. Sometimes they are tucked quite high and connected prior to PDI.
If the mechanic can't find them they tend to disconnect the other pair instead.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 



All times are GMT +1. The time now is 10:26 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Opinions expressed are not necessarily the opinions of SouthEastScoobies or any individuals directly or indirectly involved in this website. No responsibility is taken or assumed for any comments or statements made on this or any associated website. Visitors who use this website and rely on, or act on any information do so at their own judgement, discretion and or risk. SouthEastScoobies or its content providers shall not be liable for any loss or damage arising from or otherwise in connection with your use of SouthEastScoobies forums. It is not possible for the Administrators of these forums, or the Moderators participating, to fully and effectively monitor Messages that are submitted for infringement of third party rights. If you believe that any information within the forums infringes your legal rights, or gives cause for concern you should notify an Administrator or a Moderator immediately giving such information to enable the recipient to amend, delete or remove in its entirety the message, at their earliest convenience.