#1
|
|||
|
|||
cost apexi
how much would i be looking for on a apeci power fc and mapping for a 1994 wrx ?
|
#2
|
||||
|
||||
About £800 according to Simons website (although it was the old one as I can't get the new site on the iPad)
__________________
2005 Spec B 6MT - KiDO tuned (~270Bhp)
Custom exhaust - Cosworth filter - Samco Intake - Tints - Bilstein B8/B6 & STI springs - SuperPro ALK - Whiteline positive shift kit, rack mounts, rear adjustable camber bushes, front ARB mounts & strut brace, 20mm rear ARB with AVO mounts, - Hardrace Gearbox and pitch mounts - Prodrive PFF7's - Front Brembos - Kenwood CarPlay - 1/2 carbon grille - STI front splitter |
#3
|
|||
|
|||
'new' apexi ECU's for that age car dont exist to my knowledge so your looking at s/hand and then to be fitted/mapped - best to speak to the likes of Simon JGM as IMO there are probably better options out there for your money
__________________
ASPerformance 0191-4103770 PELTOR, PFC BRAKES, PAGID MOTUL, FERODO, SPEEDLINE, TRS, MINTEX, PIAA, HELLA, TEIN, WHITELINE, SUPER-PRO, MILLERS OILS online shop!! |
#4
|
|||
|
|||
Apexi's are no longer made so no new ones available.. get the occasional old stock or claiming to be new on ebay.
However on that year of car the map sensor only reads to 1.23bar.. apexi took the decision to limit the boost target to 1bar.. therefore you need a boost control kit or apexi map sensor or a boost controller.. by that point you are into more or similar money to an alcatek/simtek that comes with a 3bar map sensor if required.. Its a better ecu, map based to maf not used (which is maxxed around 340bhp on that model anyway). Simon
__________________
Jolly Green Monster Limited Full time mapper and Ecu Expert - EcuTek 99 to 2010, ESL 93 to 96, Apexi, Motec, Autronic, Link, GEMs, Simtek, Solaris/Syvecs remaps www.JollyGreenMonster.co.uk Please follow of Facebook http://www.facebook.com/pages/Jolly-...26125404073166 |
#5
|
|||
|
|||
ok a simtek sounds good to me i currently have fitted and to fit walra 255 hks filter stainless up pipe decat down pipe and ninja 2 back box yellow injectors aftermarket fuel presure reg and currently have a manuel boost controler ( 1 bar ) short shift also fitted to the car and ( live ) but have not used is a 50 shot nitros fogger system
is there any other parts would be handy to change / buy and fit before contacting you for a simtec and fitting/mapping ? many thanks |
#6
|
|||
|
|||
3port boost solenoid to replace the manual boost controller the only thing that jumps out at me
the next weak link is the intercooler.. front mount would help. Thanks Simon
__________________
Jolly Green Monster Limited Full time mapper and Ecu Expert - EcuTek 99 to 2010, ESL 93 to 96, Apexi, Motec, Autronic, Link, GEMs, Simtek, Solaris/Syvecs remaps www.JollyGreenMonster.co.uk Please follow of Facebook http://www.facebook.com/pages/Jolly-...26125404073166 |
#7
|
|||
|
|||
ok the 3 port is still there so ill get that plumbed in , ill also get a front mount fitted and give you a shout december/ new year and get a simtek and map sorted
also any idea on what the turbo is thats fitted to the car being a 1993 import and rough idea of numbers to expect/ hope for many thanks |
#8
|
|||
|
|||
Assuming its a 4door then a td05 16g. 300 to 350bhp, fair bit of variance in them.
__________________
Jolly Green Monster Limited Full time mapper and Ecu Expert - EcuTek 99 to 2010, ESL 93 to 96, Apexi, Motec, Autronic, Link, GEMs, Simtek, Solaris/Syvecs remaps www.JollyGreenMonster.co.uk Please follow of Facebook http://www.facebook.com/pages/Jolly-...26125404073166 |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|