South East Scoobies  

Go Back   South East Scoobies > The Garage > General Mechanics

Reply
 
Thread Tools
  #1  
Old 16-02-2009, 06:01 PM
lady-turbo-wrx's Avatar
lady-turbo-wrx lady-turbo-wrx is offline
Silver Member
 
Join Date: Nov 2008
Location: Kent
Posts: 869
Default intermitent idling problem

Hiya
heres my problem,my scoobs going realy well (at the moment) only for the last week or so,i have had erratic idling,but only when i put my foot down..
if i drive say normaly,it idles around 1200 but if i put my foot down hard,its idling between 2000-2500 but if i put the clutch down and rev a few times comes back generaly to 1200,or just driving the scoob normaly does it too,have tried WD40 on the throttle cable,but still not fixed it,only thought was an idle sencor

Any thoughts on this please...trace..x
Reply With Quote
  #2  
Old 16-02-2009, 08:25 PM
2-jaffacake-tone's Avatar
2-jaffacake-tone 2-jaffacake-tone is offline
Gold Member
 
Join Date: Sep 2008
Location: hastings
Posts: 1,810
Default Re: intermitent idling problem

sounds like an icv fault trace . clean it out and see if that helps
__________________
all over it jaffa style!!!
Reply With Quote
  #3  
Old 16-02-2009, 09:21 PM
Scott.T's Avatar
Scott.T Scott.T is offline
Admin, Meets/Events Organiser.... formerly known as SilverSurfer
 
Join Date: Sep 2008
Location: Hastings, East Sussex
Posts: 9,485
Default Re: intermitent idling problem

Does sound like Idle Control fault. 1200rpm is too high anyway. Should be around 850rpm.

Your model should have adjustment on the ISCV but seeing as you have a reverse inlet on their, I'm not sure if or where it would be (can't make it out on you signature).
Reply With Quote
  #4  
Old 16-02-2009, 09:24 PM
Scott.T's Avatar
Scott.T Scott.T is offline
Admin, Meets/Events Organiser.... formerly known as SilverSurfer
 
Join Date: Sep 2008
Location: Hastings, East Sussex
Posts: 9,485
Default Re: intermitent idling problem

just realised you Signature was a clicky.
The ISCV is just under your strut brace, with the grey connector on it.
Mark it's current position, then take it off and clean out with carb cleaner.
Refit where it is and try it. Then with the slotted fixing adjust to drop the idel down from 1200rpm to >1000rpm
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 



All times are GMT +1. The time now is 02:18 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Opinions expressed are not necessarily the opinions of SouthEastScoobies or any individuals directly or indirectly involved in this website. No responsibility is taken or assumed for any comments or statements made on this or any associated website. Visitors who use this website and rely on, or act on any information do so at their own judgement, discretion and or risk. SouthEastScoobies or its content providers shall not be liable for any loss or damage arising from or otherwise in connection with your use of SouthEastScoobies forums. It is not possible for the Administrators of these forums, or the Moderators participating, to fully and effectively monitor Messages that are submitted for infringement of third party rights. If you believe that any information within the forums infringes your legal rights, or gives cause for concern you should notify an Administrator or a Moderator immediately giving such information to enable the recipient to amend, delete or remove in its entirety the message, at their earliest convenience.