South East Scoobies  

Go Back   South East Scoobies > The Garage > General Mechanics

Reply
 
Thread Tools
  #1  
Old 17-10-2008, 02:19 PM
stig this stig this is offline
Regular User
 
Join Date: Sep 2008
Location: Brighton
Posts: 89
Default overboost /fuel cut.....

i had a problem with overboost a while ago @ 1.5bar so took the car to subaru gatwick they fitted a bit in the boost/sol tube and that sorted it down to 1.2bar. last week i found loose fitted "y" pipe and induction pipe so tightend all pipes and the boost went up to 1.4bar i then fitted a hks bov "sounds sweeeeet" but now when i boot it boost is just over 1.5bar was thinking about getting hks evc 4/5 rather than standard as i wanted to also upgrade to an apexi power fc ecu. any helpfull suggestions would be much appreciated its a sti v3, 6s ecu 311bhp
__________________
365bhp/ 345ftlbs api built and pat h. map
Reply With Quote
  #2  
Old 17-10-2008, 08:46 PM
Scott.T's Avatar
Scott.T Scott.T is offline
Admin, Meets/Events Organiser.... formerly known as SilverSurfer
 
Join Date: Sep 2008
Location: Hastings, East Sussex
Posts: 9,485
Default Re: overboost /fuel cut.....

Sounds like you have a leak somewhere or a sticky boost control solenoid.
Gatwick shouldn't of changed the restrictor without investigating as it's likley due to a fault/leak which the change in restrictor has masked.

Are you still running OE boost control ??

The boost control pipes should be plumbed as per my post to CJ which I have copied below :

Standard 2-port plumbing :
turbo to T-piece (restrctor in pipe)
T-piece to Actuator
Bottom branch or T-piece to Boost Control Solenoid
Then Boost conrol solenoid to inlet manifold (the little black elbow just to left of main induction hose).
Reply With Quote
  #3  
Old 18-10-2008, 01:30 PM
stig this stig this is offline
Regular User
 
Join Date: Sep 2008
Location: Brighton
Posts: 89
Default Re: overboost /fuel cut.....

Quote:
Originally Posted by SilverSurfer

Are you still running OE boost control ??

The boost control pipes should be plumbed as per my post to CJ which I have copied below :

Standard 2-port plumbing :
turbo to T-piece (restrctor in pipe)
T-piece to Actuator
Bottom branch or T-piece to Boost Control Solenoid
Then Boost conrol solenoid to inlet manifold (the little black elbow just to left of main induction hose).
Yes its a standard boost solenoid. i will check all the boost pipes and spray carb cleaner in boost sol. today cheers what boost level should i be getting as it was working good @ 1.5bar, my defi`s read 1.5bar but surrey rolling road read 1.2bar... thanks again for your help
__________________
365bhp/ 345ftlbs api built and pat h. map
Reply With Quote
  #4  
Old 18-10-2008, 07:20 PM
Scott.T's Avatar
Scott.T Scott.T is offline
Admin, Meets/Events Organiser.... formerly known as SilverSurfer
 
Join Date: Sep 2008
Location: Hastings, East Sussex
Posts: 9,485
Default Re: overboost /fuel cut.....

standard boost should be around 1bar.
if it's running 1.5 it will probably be detonating and will defo be runin ff the end of the fuel/ignition map, which is not good.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 



All times are GMT +1. The time now is 03:28 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Opinions expressed are not necessarily the opinions of SouthEastScoobies or any individuals directly or indirectly involved in this website. No responsibility is taken or assumed for any comments or statements made on this or any associated website. Visitors who use this website and rely on, or act on any information do so at their own judgement, discretion and or risk. SouthEastScoobies or its content providers shall not be liable for any loss or damage arising from or otherwise in connection with your use of SouthEastScoobies forums. It is not possible for the Administrators of these forums, or the Moderators participating, to fully and effectively monitor Messages that are submitted for infringement of third party rights. If you believe that any information within the forums infringes your legal rights, or gives cause for concern you should notify an Administrator or a Moderator immediately giving such information to enable the recipient to amend, delete or remove in its entirety the message, at their earliest convenience.